Determining the right trace width for PCB is very important to engineer. Excessively large traces consume valuable PCB space and increase the cost of PCB. This article walks through some important considerations to keep in mind for picking right trace widths while routing the PCB.
What factors are important for trace width?
The important factors to consider when selecting a trace width include:
·The current capacity of the trace
·Space availability and manufacturing limitations
·Trace termination
·Impedance
Trace Amperage (current carrying capacity)
For any given trace on the PCB, there is a maximum amount of current it can handle before it fails. Passing large current through a trace will cause it to dissipate power as heat (like a resistor), and given enough current (and time) the trace will be destroyed by either burning through, or de-laminating from the PCB there by breaking the trace. Most often we think of traces as zero resistance connecting wires between the components, but this is certainly not the case. All traces will have some sort of resistance and it is important to consider this when selecting widths. Knowing the resistance of a trace and the maximum current that will be passed through it, will help inform which width to use. So it is good to ask following questions before deciding trace widths:
What is the thickness of the copper layer?
Is the track on the outer layers (top or bottom layer)?
Is it on one of the inner layers where heat can’t escape as easily?
How long is the track?
What is the thermal coefficient of the dielectric?
Calculating the resistance of traces could be a tedious job.
In the calculator, you have to enter design specifications such as the thickness of copper, the expected maximum amperage that will pass through the trace, the length of the trace, and the acceptable increase in temperature due to the resistance of the trace. After entering these values you will be presented with a calculated trace width. It is important to note that this value is a minimum width required to meet the design criteria inputs.
The thickness parameter mentioned in the calculator is referring to the thickness of the copper layer of PCB and not the thickness of PCB itself. Copper layers used on PCBs come in fairly standard thicknesses – typically measured in ounces (oz) per square foot or Mil. For example, the most commonly used 1 oz copper board is about 1.4mils. General rule of thumb is that the thicker the copper layer, the lesser the trace width required. PCB manufacturers offer boards of various thicknesses. For example, PCBWay, unlike other popular pcb manufacturers, offers boards over wide range from 0.5 – 13 oz copper thickness.
Generally, the traces on the inner layers are required to be thicker than outer layers as the heat can’t escape easily from the inner layers. This is relevant for multilayer PCBs with more than 2 layers.
Determining the width of a trace based on the current demands is important for most power traces and high power signals, however, except power lines, most traces on PCBs pass the signals that draw negligible current. For these low power signal traces, we should look at other characteristics presented below to determine the width.
Space availability and manufacturing limitations
The size of a PCB is directly connected to the manufacturing cost of the PCB. Therefore, designers aim to keep PCBs as small as possible. The downside of reducing board size is that it can limit the available space to route traces. For low power signal traces it is generally advised to keep traces small to increase the available space available for routing. However, minimum trace width recommendations from manufacturers should be kept in mind. The minimum trace widths and spacing are manufacturer and process dependent and usually vary between 3mils and 8mils. Usually, the lower minimum widths tend to be much more expensive compared to higher minimum widths. So It is recommended to avoid trace widths less than 6mil, unless it’s absolutely necessary. The widths of 6 to 25 mils is typical for most signal traces.
Trace Termination
Sometimes, the point at which a trace meets a pad can also inform the width of a trace. In most SOIC footprints, trace widths are set to the same width as the pad they terminate to. This will avoid violating minimum spacing constraints between adjacent traces.
Impedance
Impedance is another determining factor in some applications. At low frequencies (ie. below a few MHz) impedance is not much of a concern, and the width of the traces can be set based purely on current handling requirements or manufacturing process limits. But when it comes to PCBs with higher frequency signals, the connection on the PCB starts to behave more like a transmission line than a simple short circuit conductor. That’s because the high frequency signal moving along the trace creates a magnetic field around the current flow, and an electric field (charge) between the trace. In such cases, controlled impedance is taken into consideration while designing PCBs which also include trace widths.
If you want to learn more PCB knowledge or want to order PCB products, please check PCBBUY homepage for more information.